Back to the main page Back to category Motorboats
boat details
Evinrude Johnson 15Hp 2 stroke outboard - 1985 Model completely reconditioned!
Estimated price for orientation: 865 $
Category: Motorboats
Class:
Description Year: 1985 Spec - Originally 1979 State: NSW Brand: Johnson Included Items: 100% rebuilt 15Hp Johnson Outboard, Short Sharft, Outboard Motor
With much pride we offer this 15Hp Johnson Short Shaft 1985 Specification 2 cylinder, 2 stroke outboard, complete. It has just undergone a full recondition, revocation and update, originally a 9.9Hp 1979 Model it took four 4x other units as parts to piece together this one off workshop project. Restored by a Qualified Marine Engineer (semi retired) back to pristine condition with no expenses spared. (refer list below) It is fully tested and run in ready to go. Happy to hook up to the tap and run for demonstration.This is a rear offering - Work carried Out. (over 95 Hours of T.L.C in this one).
Power Head - 2.188"Standard Bore Block acid bathed and etched then line honed.
Standard Pistons (perfect used) with new rings, Big & little end bearings, New wrist pins & clips fitted.CDI-2 Unit Complete fitted, replacing the old Points/Magneto System.New Main, Top, and Mid Bearings replace with all new Seals through out.High Compression Head with New Head Gasket fitted and tightened down to Spec..15Hp 25mm Throat Carburetor fitted with re-synchronized Linkage.ALL Carburetor Parts & Gaskets replaced Incl Fuel Float & Needle & Seat.
ALL bolt holes and threads (every one of them) cleaned of 30 Years of corrosion greased and restored.ALL Gaskets & seals replaced with NEW through-out.ALL Water Jackets removed, cleaned and etched.ALL Exhaust Housings and Water Jackets cleaned and etched.New Fuel Pump Kit Fitted.New Water Pump, impeller, Seals and grommets replacedNew Gearbox top Seals replaced.Gear Box Rebuilt (2x)
Gear Box Final Drive bearings and seals replaced.Just about everything else is done & fixed, Eg: Tiller Arm linkages matched & mated, the Claw mechanism fixed, the Claw screws fasteners changed to NEW, etc, etc...
Tuned to factory specifications and idles like a kitten. And the Nice bit... Engine, Case, Leg & Gear Box all Painted with two Coats of Acrylic Enamel and Clear Top Coat - Detailed with Red.No Fuel Tank. - No Trolley
Full restore parts list, Pics and Videos with the Sale.In Short basically its a New Outboard, with a classic Vintage twist - Water Tested to 6100 RPM on 12"Savage Tinny.
This Classic Collector's "Outboard" would suite someone looking for a "New Condition" outboard - WITHOUT 30 YEARS OF CORROSION IN IT!
Buy it Now at $865.00 = Strictly No lower Offers!
Any Inspection Welcome by appointment only. - Located in N.S.W - at Menai - Sydney, Post Code 2234.
Selling, as we are onto the next project now and this needs to be "On-Sold"_ If unsold, this add may be removed, as it is advertised elsewhere.
Genuine Buyers Only may Email via eBay only or Contact Stephen. Mobile 0412 673 460.
Description
| Year: | 1985 Spec - Originally 1979 | State: | NSW |
| Brand: | Johnson | Included Items: | 100% rebuilt 15Hp Johnson Outboard, Short Sharft, Outboard Motor |
With much pride we offer this 15Hp Johnson Short Shaft 1985 Specification 2 cylinder, 2 stroke outboard, complete. It has just undergone a full recondition, revocation and update, originally a 9.9Hp 1979 Model it took four 4x other units as parts to piece together this one off workshop project. Restored by a Qualified Marine Engineer (semi retired) back to pristine condition with no expenses spared. (refer list below) It is fully tested and run in ready to go. Happy to hook up to the tap and run for demonstration.This is a rear offering - Work carried Out. (over 95 Hours of T.L.C in this one).
Power Head - 2.188"Standard Bore Block acid bathed and etched then line honed.
Standard Pistons (perfect used) with new rings, Big & little end bearings, New wrist pins & clips fitted.CDI-2 Unit Complete fitted, replacing the old Points/Magneto System.New Main, Top, and Mid Bearings replace with all new Seals through out.High Compression Head with New Head Gasket fitted and tightened down to Spec..15Hp 25mm Throat Carburetor fitted with re-synchronized Linkage.ALL Carburetor Parts & Gaskets replaced Incl Fuel Float & Needle & Seat.
ALL bolt holes and threads (every one of them) cleaned of 30 Years of corrosion greased and restored.ALL Gaskets & seals replaced with NEW through-out.ALL Water Jackets removed, cleaned and etched.ALL Exhaust Housings and Water Jackets cleaned and etched.New Fuel Pump Kit Fitted.New Water Pump, impeller, Seals and grommets replacedNew Gearbox top Seals replaced.Gear Box Rebuilt (2x)
Gear Box Final Drive bearings and seals replaced.Just about everything else is done & fixed, Eg: Tiller Arm linkages matched & mated, the Claw mechanism fixed, the Claw screws fasteners changed to NEW, etc, etc...
Tuned to factory specifications and idles like a kitten. And the Nice bit... Engine, Case, Leg & Gear Box all Painted with two Coats of Acrylic Enamel and Clear Top Coat - Detailed with Red.No Fuel Tank. - No Trolley
Full restore parts list, Pics and Videos with the Sale.In Short basically its a New Outboard, with a classic Vintage twist - Water Tested to 6100 RPM on 12"Savage Tinny.
This Classic Collector's "Outboard" would suite someone looking for a "New Condition" outboard - WITHOUT 30 YEARS OF CORROSION IN IT!
Buy it Now at $865.00 = Strictly No lower Offers!
Any Inspection Welcome by appointment only. - Located in N.S.W - at Menai - Sydney, Post Code 2234.
Selling, as we are onto the next project now and this needs to be "On-Sold"_ If unsold, this add may be removed, as it is advertised elsewhere.
Genuine Buyers Only may Email via eBay only or Contact Stephen. Mobile 0412 673 460.
Power Head - 2.188"Standard Bore Block acid bathed and etched then line honed.
Standard Pistons (perfect used) with new rings, Big & little end bearings, New wrist pins & clips fitted.CDI-2 Unit Complete fitted, replacing the old Points/Magneto System.New Main, Top, and Mid Bearings replace with all new Seals through out.High Compression Head with New Head Gasket fitted and tightened down to Spec..15Hp 25mm Throat Carburetor fitted with re-synchronized Linkage.ALL Carburetor Parts & Gaskets replaced Incl Fuel Float & Needle & Seat.
ALL bolt holes and threads (every one of them) cleaned of 30 Years of corrosion greased and restored.ALL Gaskets & seals replaced with NEW through-out.ALL Water Jackets removed, cleaned and etched.ALL Exhaust Housings and Water Jackets cleaned and etched.New Fuel Pump Kit Fitted.New Water Pump, impeller, Seals and grommets replacedNew Gearbox top Seals replaced.Gear Box Rebuilt (2x)
Gear Box Final Drive bearings and seals replaced.Just about everything else is done & fixed, Eg: Tiller Arm linkages matched & mated, the Claw mechanism fixed, the Claw screws fasteners changed to NEW, etc, etc...
Tuned to factory specifications and idles like a kitten. And the Nice bit... Engine, Case, Leg & Gear Box all Painted with two Coats of Acrylic Enamel and Clear Top Coat - Detailed with Red.No Fuel Tank. - No Trolley
Full restore parts list, Pics and Videos with the Sale.In Short basically its a New Outboard, with a classic Vintage twist - Water Tested to 6100 RPM on 12"Savage Tinny.
This Classic Collector's "Outboard" would suite someone looking for a "New Condition" outboard - WITHOUT 30 YEARS OF CORROSION IN IT!
Buy it Now at $865.00 = Strictly No lower Offers!
Any Inspection Welcome by appointment only. - Located in N.S.W - at Menai - Sydney, Post Code 2234.
Selling, as we are onto the next project now and this needs to be "On-Sold"_ If unsold, this add may be removed, as it is advertised elsewhere.
Genuine Buyers Only may Email via eBay only or Contact Stephen. Mobile 0412 673 460.