I finally purchased the boat and was mine. I decided to redone the engine and "freshen" things up. I removed the 1970's 454 that was in the boat and dropped it off at RPM Engines in Westwood, New Jersey. I advised the builder "Doc" that I wanted a fully built engine with all quality internals. The block was checked for cracks, etc etc. I bought all new forged internals; Crank, Rods and Pistons. I bored the engine .30, the compression is 8.5-1. The heads are edlebrock marine performer rpm heads with all crane internals; push rods, roller rockers and valves. I went with a crane comp roller cam. The engine has maybe 20 hours on it and was only used in fresh water 5 times. The motor is perfectly healthy, sounds absolutely beautiful and runs absolutely phenomenal. I have all paperwork for the engine build. I bought brand new Stainless Marine exhaust manifolds and risers mounted to a 3" gil stainless steal tip. The exhaust has a 1970's corvette 750cc carburetor which was rebuilt summer of 2015 by Steves Carburetors in Lyndhurst, New Jersey. The motor mounts for the motor are custom to allow that engine to mount and sit properly in the boat. The TRS drive and transmission were fully rebuilt in the late 2000's and has zero issues. I know the TRS drive is an old and "obsolete" but the drive was removed from a 40' cruiser which was mated to a 454 (boat had twin engines and drives). The drive/transmission was opened up and fully rebuilt with all forged internals. This drive is pretty much bullet proof. I don't think you will ever "destroy" this drive. Specifically since it was designed to push a 40' boat which weights triple of what my boat does. I have never had any issues what so ever with the drive, engages into gear smoothly and works as it should. The drive is mated to a 24inch prop. The boat moves! The boat has a gil stainless steel water strainer, gil stainless steel exhaust tips, exhaust tip housing, I bought new new oil and power steering pump oil coolers in the spring of 2014. I bought a brand new steering piston, installed new cables for the steering as well.I am honestly forgetting somethings but I replaced just about every single nut and bolt when I rebuilt the engine. I had the drives removed and has all new seals installed, new gimble housings, new TRS drive pistons (lift the drive up and down) all brand new and replaced. Money was not a factor when I decided to fix all the issues. The bad:
The boat is a 1979 and even though the boat was redone in the mid 1990's there are some small stress cracks which is common on all fiber glass boats. The stress cracks are on the rear of the boat where the latch is. The interior does show very slight fading but overall is in good shape.
The Tachometer doesn't work perfectly
The engine bay was painted Battleship Gray and some areas need to be slightly touched up. If you have any questions, please call me I could explain more on the phone then in this listing. I also am in contact with the original builder if you have any questions. I will guarantee you will not find a more solid boat than what I have for sale. This boat in todays day and age would cost someone over 60-80k to duplicate. I look at the follow as a realistic approach to duplicate what I havePurchase a Donzi Hornett $12,000.00-$15,000.00Fiberglass work and paint-$20,000.00Interior $6,000.00-$8,000.00Motor and Drive $12,000Without even getting into more details, just what I mentioned above would cost someone at least $50,000.00. I WANT a fraction of that.
Trailer:Load Rite galvanized aluminum in great condition. I replaced all four wooden bunks and installed new carpet.All bearings were packed and are in good shapeBrakes are in good shape as wellEverything works as it shouldIf you are serious about purchasing the boat, please call me and ask specific questions you may have. If you need more or better pictures, let me know.This is a short video of the builder tuning the carbs last year. I only took the boat out in the water one time last season. Please click the link! The boat is filthy in the pictures, I will have the boat professionally detailed for the new buyer!